• Português
  • Русский
  • Español
  • italiano
  • Deutsh
  • Français
  • Polski
  • العربية

Product Categories

    Xhorse & VVDI Products

    Name: VVDI RKE BOX Support 6V/9V/12V Remote Control Switching Box
    SKU: TM005522
    Category: Xhorse & VVDI Products
    Stock: in stock


    VVDI RKE BOX Support 6V/9V/12V Remote Control Switching Box

    auto key-tb.jpg

    Product Description

    Xhorse VVDI RKE BOX is applied at the following aspects:
    1. To change the original straight remote control to folding remote
    2. No method or apparatus temporarily to add a new remote control
    3. Temporary replacement because of the original out of stock
    4. Only one remote for the original car (such as the Chinese, Besturn, etc.)
    5. To seek low-cost remote control instead of the expensive original one
    Note: at least one original remote control for use of the kitL

    VVDI RKE BOX  Remote Control Switching Box Support 6V/9V/12V

     1.Power options: connect 3V remote control by default, not any welded joints connection.
     If you connect remote control of 6V, 9V or 12V, please take the main box apart and select
     the corresponding joints showed on the the following image.
     Example: To connect 6V remote control,you should just have 6v welded joints connected.
    2. Wiring Description: 
     Remove the circuit boards in the original remote control, and connect to the main unit as
     the right picture shows (connect the white wire to buttons, red to the positive, black to
     the negative)
     Note: 3 kinds of remote button: 2-feet, 4-feet and 5 feet buttons
     4-feet and 5-feet buttons: no direction distinction, but it must be soldered at the diagonals
     2-feet buttons: no direction distinction, and respectively solder the two feet
     original remote control
     remote wiring diagram
    Important: Do not reverse the power cord on the remote control
    3. To get power via OBD or 12V constant power from the car
    4. Key/ remote matching and clearing
    Matching steps:
     Press SET button on the Host box (in the internal hole at the side of unit), then the buzzer
     beep twice, to go into the matching state
     Press any button on the new remote for a while until the buzzer beep continuously.

     Key matching is completed.
     Repeat the previous two steps to add another new key.
     Up to six keys to match for one Host box; the key matching will fail if more
     In the matching state, the buzzer beeps once if the key cannot be detected for more than
     10 seconds, and then automatically exit the matching state to go into the normal working state.
     Clearing Steps:
     Press SET button for a while until the buzzer beep continuously. All the keys matched previously
     are cleared and return to factory state

     If the key is lost or not to use, you can erase all the keys and then re-add all lost keys toensure safety.
     Key to be added
     SET button
    5. To add the key embryo and anti-theft chip to the remote control
    Package Including:
     1pc x VVDI RKE BOX
     2pc x key

    Weight: 0.2KG   ( 0.44LB )
    Package: 23cm*17cm*4cm        ( Inch: 9.06*6.69*1.57 )


    car key-db.jpg

    Related Products


    ShenZhen Emyray Tech Co.,Ltd.       Tel: +86-755-83376535     Mob:+86-135-4415-9828      Skype: autokeymall03      QQ: 3237124068

    Warm prompt: our company website products, only for a locksmith industry personnel, the locksmith staff must provide valid
    documents to the company
    for the record after just can buy! Thanks for your cooperation!   Thank you very much!